|
How to change the I/O voltage of LDO after boot?
|
|
0
|
9
|
February 6, 2026
|
|
What are the HDMI PCB layout application notes from iWave?
|
|
0
|
12
|
February 6, 2026
|
|
What is the calculated MTBF for ZU11EG-based iG-G35M SOM?
|
|
0
|
15
|
February 6, 2026
|
|
How to implement SOMPWR_EN in iG-G35M SOM?
|
|
0
|
8
|
February 6, 2026
|
|
What is the MIO Pin Multiplexing Conflict: On-SOM GEM0 Ethernet vs. PS-PCIe Endpoint Reset on iG-G35D?
|
|
0
|
14
|
February 6, 2026
|
|
What is the Power Management and Thermal Protection Strategy used in iG-G35M SOM?
|
|
0
|
11
|
February 6, 2026
|
|
What is the JTAG Interface & Reset Logic used in iG-G35M SOM?
|
|
0
|
15
|
February 6, 2026
|
|
Is 240ohm MIPI D-PHY termination resistor present on the iG-G35M SOM HP Bank?
|
|
0
|
15
|
February 6, 2026
|
|
How is the USB_ID signal connection in iG-G35M SOM and how to configure to USB as Host?
|
|
0
|
10
|
February 6, 2026
|
|
What is the Propagation Delay for iG-G30M SOM?
|
|
0
|
11
|
February 6, 2026
|
|
What is the HP Bank Voltage Configuration in G35M SOM ZU19EG?
|
|
0
|
15
|
February 5, 2026
|
|
What are the I/O mapping and Ethernet PHY configuration settings for G36S SOM?
|
|
0
|
19
|
February 5, 2026
|
|
What does the PS_ERROR_OUT-LED status indicate and how the boot mode indicators are verified?
|
|
0
|
26
|
February 5, 2026
|
|
How to interface 3.3V Peripherals with 1.8V PS_IO signals on G35D DevKit?
|
|
0
|
11
|
February 5, 2026
|
|
How to enable eMMC write protection capabilities in hardware (G35M SOM)?
|
|
0
|
16
|
February 5, 2026
|
|
What is the CPU Frequency Specifications for i.MX8M Plus iG-G40M?
|
|
0
|
12
|
January 30, 2026
|
|
What are the Boot Switch & Debug Port Settings and how to Power ON the i.MX95 SMARC SOM Development Platform with iG-G61D?
|
|
0
|
31
|
January 28, 2026
|
|
Not able to access any of the eFUSEs via software. What is the procedure to program the eFUSEs & enable secure boot in Zynq Ultrascale+ devices?
|
|
0
|
20
|
January 16, 2026
|
|
How to compile C code directly on the SOM's command prompt?
|
|
0
|
12
|
January 16, 2026
|
|
What is the the procedure to SD boot the Zynq MPSoC Ultrascale+ board which supports SD boot?
|
|
0
|
16
|
January 16, 2026
|
|
How to identify the internal powers are stable in G35M SOM?
|
|
0
|
15
|
January 16, 2026
|
|
How to identify the Processor System (PS) is out of control or under error?
|
|
0
|
21
|
January 16, 2026
|
|
What are the required switch settings to boot G35D from SD card?
|
|
0
|
12
|
January 16, 2026
|
|
Does G35P support watchdog?
|
|
0
|
6
|
January 16, 2026
|
|
How to enable DMA for USB and Ethernet in G40M i.MX8MP?
|
|
0
|
10
|
January 14, 2026
|
|
How to enable Wi-Fi network on G27S i.MX8 QM/QP with Ubuntu 22.04?
|
|
0
|
20
|
January 14, 2026
|
|
How to remove the Chromium layer from compilation process in G40S i.MX8M Plus Pico ITX SOM?
|
|
0
|
15
|
January 14, 2026
|
|
Is 4-lane MIPI Display validated in G27S i.MX8QM SOM?
|
|
0
|
10
|
January 14, 2026
|
|
Where can I find the detailed pinmux mapping for the i.MX8QM Pico ITX expansion connectors in the hardware user guide?
|
|
0
|
10
|
January 14, 2026
|
|
What is the voltage level on all pins of the headers for G27S i.MX8QM Pico ITX SBC?
|
|
0
|
11
|
January 14, 2026
|