|
What is the required recovery step if the expected kernel modules are missing from the "lsmod" output?
|
|
0
|
2
|
April 17, 2026
|
|
Is it possible to do the current and power consumption for each interface in G36M SOM?
|
|
0
|
3
|
April 16, 2026
|
|
Is it possible to disable the Gigabit Ethernet PHY on the SOM to conserve power?
|
|
0
|
2
|
April 16, 2026
|
|
Why the .bat file is not found in the Android provided package and what is the procedure to download and proceed with the test case?
|
|
0
|
2
|
April 16, 2026
|
|
How and when the voltage regulators of G50S i.MX91 SBC SOM are activated and ready?
|
|
0
|
2
|
April 15, 2026
|
|
Does i.MX93 chipset support an internal RTC Controller? Will G50M SOM manage the battery and charge it?
|
|
0
|
8
|
April 15, 2026
|
|
Is it possible to configure bank 64 voltage in G30M?
|
|
0
|
7
|
April 14, 2026
|
|
How is the 1.5V regulated for the VCC_PSBATT pin on the MPSoC G36M ZU3EG?
|
|
0
|
4
|
April 14, 2026
|
|
How to read the SOC temperature in G30M ZU7CG?
|
|
0
|
3
|
April 14, 2026
|
|
What are the voltage levels for PL HD Banks 45 and 46, and how are they configured in the FSBL?
|
|
0
|
3
|
April 14, 2026
|
|
Can SDIO be used as GPIO? How to change the SDIO voltage to 1.8V or 3.3V?
|
|
0
|
6
|
April 13, 2026
|
|
How to set the root password in YOCTO in G33M i.MX8M SMARC SOM?
|
|
0
|
10
|
April 13, 2026
|
|
How to enable Wi-Fi interface, configure Wi-Fi hotspot and how to enhance its signal strength on G33M i.MX8M SMARC SOM?
|
|
0
|
12
|
April 13, 2026
|
|
How to remotely update the ZU19EG firmware (either bistream, BOOT files or rootfs) via ethernet interface in G35D?
|
|
0
|
9
|
April 12, 2026
|
|
Does G41G require RTK SKU GPS to support Dead Reckoning?
|
|
0
|
3
|
April 10, 2026
|
|
Does the TBox be certified for any cyber security standards (UNECE R155 \ ISO21434)?
|
|
0
|
3
|
April 10, 2026
|
|
Does GPS support Dead Reckoning (DR) in G41G?
|
|
0
|
3
|
April 10, 2026
|
|
Is Wayland backend used in i.MX8 platform (in Linux)?
|
|
0
|
12
|
April 9, 2026
|
|
Which USB PHY is used in G36M? Is it possible to adjust USB PHY to the 38.4MHz rate, also modifying the USB PHY reference clock will it impact the Linux Device Tree/Driver?
|
|
0
|
4
|
April 9, 2026
|
|
What reference is used to generate the Synthesizer Clocks (PLL’s) in G36M MPSoC SOM?
|
|
0
|
6
|
April 8, 2026
|
|
What is the switching frequency of the switching power regulators used in G36M SOM?
|
|
0
|
3
|
April 8, 2026
|
|
How does CARRIER_PWR_EN pin behave in G50S i.MX91 SBC SOM?
|
|
0
|
4
|
April 8, 2026
|
|
Does VRTC_3V0 feed the VCC_PSBATT signal in G36M SOM?
|
|
0
|
4
|
April 7, 2026
|
|
Is SYS_SYNC_CLOCKP/SYS_SYNC_CLOCKN supported in G36D Dev Kit?
|
|
0
|
4
|
April 7, 2026
|
|
Does RZ/G1E G22M include a supported internal thermal sensor on the SOM?
|
|
0
|
5
|
April 7, 2026
|
|
How to disable SATA & display port from system-user.dtsi in G30M?
|
|
0
|
4
|
April 7, 2026
|
|
What are the required configuration settings for the QEMU emulator on G30M SOM?
|
|
0
|
5
|
April 7, 2026
|
|
What is the correct procedure for manually reloading the TCAN kernel module to ensure it is properly initialized?
|
|
0
|
3
|
April 6, 2026
|
|
How are the SPI Clock, PS and PL IO pins connected to the B2B connector in G30M?
|
|
0
|
7
|
April 6, 2026
|
|
How does the FORCE_RECOVERY# pin work & Is this also connected to BOOT_MODE or BOOT_SEL pin?
|
|
0
|
5
|
April 6, 2026
|