|
About the ZU19/ZU17/ZU11 category
|
|
0
|
2
|
May 15, 2026
|
|
How to enable FMC+ power using Bare-Metal for ZU11EG SoM?
|
|
0
|
1
|
June 9, 2026
|
|
Whether it is possible to configure a different I/O voltage for Bank 94 independently, or is a common voltage mandatory across all banks connected to PMIC LDO4?
|
|
0
|
2
|
June 5, 2026
|
|
What license is required for generating the bitstream while using JESD IPs?
|
|
0
|
6
|
May 26, 2026
|
|
How the PMIC LDO1 and LDO4 are configured in G35M ZU11EG SoM
|
|
0
|
4
|
May 26, 2026
|
|
How the FMC I2C lines are connected from the I2C Mux Switch settings in G35D ZU11EG?
|
|
0
|
3
|
May 26, 2026
|
|
What are the different methods to program eMMC?
|
|
0
|
4
|
May 25, 2026
|
|
How to make sure if all the images are avaialble in eMMC?
|
|
0
|
1
|
May 25, 2026
|
|
What is the HD Bank IO levels of G35M ZU19/ZU17/ZU11 SOM and can it be configured in software?
|
|
0
|
5
|
May 6, 2026
|
|
How to switch from sysvinit to systemctl in the rootfs in G35M MPSoC SOM?
|
|
0
|
6
|
May 4, 2026
|
|
What are the U-Boot commands to initialize and start an SD boot on iWave SOM?
|
|
0
|
8
|
April 30, 2026
|
|
What are the steps to be followed to add the .bit file to the boot image?
|
|
0
|
5
|
April 30, 2026
|
|
How to locate and control the PMOD GPIOs on the G35D devkit within the Zynq UltraScale+ MPSoC environment?
|
|
0
|
11
|
April 24, 2026
|
|
Does G35M SOM support BBRAM? Is there an application note for BBRAM?
|
|
0
|
4
|
April 20, 2026
|
|
How to clean the FSBL firmware build and is it possible to provide work directories for pmufw, atf and u-boot?
|
|
0
|
5
|
April 17, 2026
|
|
How to remotely update the ZU19EG firmware (either bistream, BOOT files or rootfs) via ethernet interface in G35D?
|
|
0
|
11
|
April 12, 2026
|
|
How to load Vivado ML Enterprise License Edition?
|
|
0
|
62
|
April 1, 2026
|
|
How would to add arguments to the boot command while isolating core 3 in the yocto image?
|
|
0
|
7
|
March 30, 2026
|
|
How to build the image(s) with a read-only file system in G35M SOM?
|
|
0
|
5
|
March 30, 2026
|
|
How to obtain the required Vivado license to proceed with G35D development kit?
|
|
0
|
8
|
March 28, 2026
|
|
While building a custom bitstream, why does the Xilinx IP shows that the license is only available for simulation?
|
|
0
|
4
|
March 27, 2026
|
|
What is the resistor value of VRP pin G35M SOM?
|
|
0
|
7
|
March 19, 2026
|
|
How to solve the Boot Issues while booting from SD Card using G35M SOM?
|
|
0
|
7
|
March 18, 2026
|
|
What is the solution when G35M gets stuck after loading BL31 in the Petalinux?
|
|
0
|
10
|
March 16, 2026
|
|
Is it advisable to leave SD1_PWR & SD_CD left unconnected?
|
|
0
|
6
|
March 14, 2026
|
|
What is the SW6 Switch settings for connecting to the board via JTAG Cable?
|
|
0
|
9
|
March 14, 2026
|
|
What is the supported voltage and the current drawn in VRTC pin, G35M SOM?
|
|
0
|
8
|
March 13, 2026
|
|
What is the specific Vivado license is required to work with the devices in G35D Devkit?
|
|
0
|
12
|
March 11, 2026
|
|
Which clock is an input to G35D and which is an output from G35D via the FMC/FMC+?
|
|
0
|
7
|
March 11, 2026
|
|
Which lane of PS-GTR is used for the USB0 in G35D Development kit?
|
|
0
|
11
|
March 7, 2026
|